The model for the emitter and receiver tubes was revised to have a smaller hole for the receiver since it would be glued in place. A second LED mounting location was added but there was no need for a tube since it would simply be an indicator LED. An RGB LED will likely be used since they are inexpensive and plenty of outputs are still available on the controller.
E6000 glue was used to hold the TSOP4856 receiver and LED holders held the emitter and an RGB LED. Black liquid tape was used to coat the back of the receiver. A divider was going to be added to the model which would help eliminate any light leakage on the backside of the unit but it was decided that a light-blocking layer on the back would be simpler.
Downloadable Files:
The rest of the posts for this project have been arranged by date.
First time here?
Completed projects from year 1.
Completed projects from year 2.
Disclaimer for http://24hourengineer.blogspot.com/
This disclaimer must be intact and whole. This disclaimer must be included if a project is distributed.
All information in this blog, or linked by this blog, are not to be taken as advice or solicitation. Anyone attempting to replicate, in whole or in part, is responsible for the outcome and procedure. Any loss of f
functionality, money, property or similar, is the responsibility of those involved in the replication.
All digital communication regarding the email address 24hourengineer@gmail.com becomes the intellectual property of Brian McEvoy. Any information contained within these messages may be distributed or retained at the discretion of Brian McEvoy. Any email sent to this address, or any email account owned by Brian McEvoy, cannot be used to claim property or assets.
Comments to the blog may be utilized or erased at the discretion of the owner. No one posting may claim claim property or assets based on their post.
This blog, including pictures and text, is copyright to Brian McEvoy.
2015-10-10 (Sa)
Emitter and receiver tube model
E6000 glue was used to hold the TSOP4856 receiver and LED holders held the emitter and an RGB LED. Black liquid tape was used to coat the back of the receiver. A divider was going to be added to the model which would help eliminate any light leakage on the backside of the unit but it was decided that a light-blocking layer on the back would be simpler.
Glue to hold receiver in place
Black liquid tape used to block light on the back side
The sensor
Downloadable Files:
- Common OpenSCAD files
- Servo footprints for OpenSCAD.
- Arduino Code for wired keyboard
- Spreadsheet for chords.
- Wrist mount
- Terminal board
- Input voltage
- USB
- Make base for keyboard
- Spacers
- Magnet mounts
- Integrate:
- Enclosure for each controller
- Potentiometer access
- Activation switch
- Debug
- Test
- Refine
- Repeat
- Write instructions
- Compress and link to all files
- OpenSCAD files
- STL models
- Arduino code
- Make diagram with every part labeled
- Schematic for servo controller
First time here?
Completed projects from year 1.
Completed projects from year 2.
Disclaimer for http://24hourengineer.blogspot.com/
This disclaimer must be intact and whole. This disclaimer must be included if a project is distributed.
All information in this blog, or linked by this blog, are not to be taken as advice or solicitation. Anyone attempting to replicate, in whole or in part, is responsible for the outcome and procedure. Any loss of f
functionality, money, property or similar, is the responsibility of those involved in the replication.
All digital communication regarding the email address 24hourengineer@gmail.com becomes the intellectual property of Brian McEvoy. Any information contained within these messages may be distributed or retained at the discretion of Brian McEvoy. Any email sent to this address, or any email account owned by Brian McEvoy, cannot be used to claim property or assets.
Comments to the blog may be utilized or erased at the discretion of the owner. No one posting may claim claim property or assets based on their post.
This blog, including pictures and text, is copyright to Brian McEvoy.
2015-10-10 (Sa)
Comments
Post a Comment